In-situ S2XP Restrictor for TROLL 9500—Installation and Ca Manuel d'utilisateur télécharger pdf

Instruction Sheet

TROLL

9500 S2XP Restrictor Installation and Calibration

Part number 0085490, Rental R79420

Overview

The S2XP restrictor is shipped in two pieces. The

restrictor must be installed in separate steps to allow for

sensor calibration.

It is recommended you follow all steps in this instruction

sheet to properly set up your TROLL 9500 S2XP

system.

Contents

Figure 1.1 Contents of the shipping container

1 TROLL 9500 Instrument

2 S2XP restrictor, part A

3 Quick Cal solution

4 S2XP restrictor, part B

5 Sodium sulfite solution

6 Accessories kit

7 RDO sensor; TROLL Com

8 Bubbler (not shown)

Units may contain other equipment.

pH, ORP, and Conductivity Calibration

1. Detach the Cal Cup from the TROLL 9500. The Cal

Cup contains a small amount of liquid to hydrate the

pH sensor during shipment. Discard this liquid.

2. Thoroughly rinse the sensors with clean water.

3. Fill the Cal Cup to the fill line with Quick Cal solution.

Reinstall the Cal Cup on the TROLL 9500. See

Figure 1.2. Do not over-tighten.

Figure 1.2 Calibration using Quick Cal in the Cal Cup

4. In Win-Situ 4, click on Parameters in the Navigation

tree.

5. Click Quick Cal. Select pH, ORP, and Conductivity.

6. Click Start. You must hold the TROLL 9500 vertically

for proper calibration.

7. Allow the calibration to run until indicators reach

Stable. Check calibration coefficients to ensure a

proper calibration.

Information subject to change without notice. In-Situ, In-Situ logo, Baro Merge, BaroTROLL, HERMIT, iSitu, Pocket-Situ, RDO,

RuggedCable, RuggedReader, TROLL, and Win-Situ are trademarks or registered trademarks of In-Situ Inc.

08/2013 | Rev. 005 | 0085492

1 2 3 4 5

Instruction Sheet 1

Résumé du contenu

Page 1 - Instruction Sheet

Instruction SheetTROLL®9500 S2XP Restrictor Installation and CalibrationPart number 0085490, Rental R79420OverviewThe S2XP restrictor is shipped in tw

Page 2

Instruction SheetpH slope Between -50 to -66 mV/pHpH offset 350 - 450 mVORP offset Between -20 and +20 mVK Cell Low 0.30 - 0.39 cm-1K Cell High 4.4 -

Page 3

Instruction Sheet10. Refresh Win-Situ 4 to ensure all sensors are correctlyattached to the TROLL 9500. pH, ORP, Conductivity,and Rugged Dissolved Oxyg

Page 4

Instruction Sheet5. In Win-Situ 4, click Run in the Zero Oxygen Pointscreen. Follow the on-screen instructions to completethe 0% calibration point.6.

Page 5

Instruction SheetFigure 1.14 Removing the pH/ORP sensor5. Remove the conductivity sensor using the removaltool. Note the sensor's port location (

Commentaires sur ces manuels

Pas de commentaire

In-situ S2XP Restrictor for TROLL 9500—Installation and Ca Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour l'eau In-situ S2XP Restrictor for TROLL 9500—Installation and Ca. In-Situ S2XP Restrictor for TROLL 9500—Installation and Calibration Instructions User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour l'eau In-situ S2XP Restrictor for TROLL 9500—Installation and Ca