In-situ Flow Cell for Low-Flow System with RDO Sensors (pu Manuel d'utilisateur télécharger pdf

RDO sensor

For best results, perform a 2-point calibration at these points before going into the

ﬁeld.

100% calibration point:

Fill bubbler cup with clean water. Turn on the pump, regulate with the pinch a.

valve. Insert the TROLL 9500 into the bubbler, resting the RDO adapter

plate on the rim of the cup. Allow 5-10 minutes for temperature and oxygen

equilibration in the water. Select RDO in the software Navigation tree, click

the Calibrate button, then click Run.

When readings have stabilized, click b. Next. Continue with the Zero Oxygen

Point for a 2-point calibration.

0% calibration point:

Fill the orange-based cal cup with sodium sulﬁte a.

(Na

) solution and slide it up around the RDO

sensor until the cap and thermistor are completely

submerged. Be sure that there are no air bubbles

on the foil.

Select b. Run in the Zero Oxygen Point screen. When

readings have stabilized, click Next, then Finish to

ﬁnalize the calibration.

Rinse c. very thoroughly after calibrating in sodium

sulﬁte.

The RDO sensor is now calibrated and ready to use.

Turbidity sensor:

The sensor has been factory-calibrated over its full range (0

to 2000 NTU). If ﬁeld calibration is required, we recommend a zero point calibration.

Use deionized water and the clear ﬂow cell. Make sure that the 3-way valve on the

inﬂow port is closed.

In the ofﬁce: Assemble the site data6

The software wizard will prompt for the following information for the output report:

• Well diameter & depth • Pump model & type • Tubing type

• Screen length • Depth to water, top of screen & pump intake

• Tubing inner diameter and length (for software volume calculations)

Install batteries1

Install D-cells in the TROLL 9500a. : Remove the battery

compartment cover, insert batteries, replace cover, and tighten.

Install and charge the RuggedReader battery pack: b.

This process is illustrated in the RuggedReader Quick Start.

To calibrate 100% dissolved oxygen, install alkaline D-cells in the c.

portable air pump as shown on the diagram inside the lid.

Connect the cable2

Remove the red dust caps. Insert the TROLL 9500 connector a.

into the cable connector. Push, twist, and click to lock. The

“click” ensures that the cable is securely attached.

Connect the TROLL Com to the other end of the cable.b.

Install software on your desktop/laptop PC from the 3

In-Situ

software CD

Win-Situ•

Microsoft•

ActiveSync

: Click on Microsoft Tools, select ActiveSync 4.X.

Win-Situ Sync •

TIP: Although Pocket-Situ 4 is pre-installed on the RuggedReader. You need

ActiveSync and Win-Situ Sync on the PC to transfer ﬁles between the computers.

In the ofﬁce: Launch the software4

Connect the TROLL 9500 to the PC and launch Win-Situ 4. Click a. Next through 4

screens of the Connection Wizard to set up the COM port.

Select the Com Port, tap b. Find.

TIP: Calibration and low-ﬂow setup can optionally be done on the RuggedReader using

Pocket-Situ 4.

In the ofﬁce: Calibrate the water quality sensors5

pH, ORP, and conductivity sensors

Remove the hydration bottle from the pH/ORP sensor. a. Save it to

keep the sensor hydrated between uses.

Use the orange-base cal cup with cutout and indentation. Fill with b.

Quick Cal, slide it up around the sensors, including the RDO cable.

In Win-Situ, tap c. Parameters, tap QuickCal, follow the Wizard.

TIP: Detailed steps for calibration and low-ﬂow software are in the MP TROLL 9500

Operator’s Manual on the software CD.

RDO cable outside cup

RDO sensor inside cup

Low-Flow with

RDO

Optical Dissolved Oxygen

Quick Start

Bottom Layer of Case

Multi-Parameter

TROLL

9500

with RDO, Conductivity,

Turbidity (optional),

& pH/ORP sensors—

Remove hydration

bottle from pH/ORP

sensor before use!

Quick Cal

Solution

6’

Cable

Air pump

Flow

cell

Cal cup

for Quick Cal

Bubbler

contains

batteries

Hardware ﬁttings

for ﬂow cell

Alkaline batteries

for TROLL 9500

Top Layer of Case

RuggedCable

™

TROLL

Com

TROLL

9500

Flow cell

RDO cable inside cup,

RDO sensor outside cup

12 V adapter

for RuggedReader PC

AC adapter

for RuggedReader

RuggedReader

battery

Win-Situ

software CD

and Quick Start Guides

TROLL

Com

serial comm cable

USB cable

for RuggedReader PC

RuggedReader

handheld PC

TROLL 9500

maintenance kit

Low-Flow with RDO

Quick Start Guide

Low Flow Base Plate

(not pictured)

1 2

Low-Flow with RDO 2

Résumé du contenu

Page 1

RDO sensorFor best results, perform a 2-point calibration at these points before going into the ﬁeld.100% calibration point: Fill bubbler cup with cle

Page 2 - Low-Flow with RDO

Information is subject to change without notice. In-Situ and the In-Situ logo, Win-Situ, TROLL, BaroTROLL, RuggedReader, RuggedCable, and RDO are trad

Commentaires sur ces manuels

Pas de commentaire

In-situ Flow Cell for Low-Flow System with RDO Sensors (pu Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour l'eau In-situ Flow Cell for Low-Flow System with RDO Sensors (pu. In-Situ Flow Cell for Low-Flow System with RDO Sensors (purchased after 09/2008) User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour l'eau In-situ Flow Cell for Low-Flow System with RDO Sensors (pu