In-situ RuggedCable for Aqua TROLL—Male connector end + st Manuel d'utilisateur télécharger pdf

Information Sheet

Catalog No. 0053310

SHORT STRIPPED & TINNED

CABLE

with Male Twist-Lock Connector

Desiccant

Dust cap—Remove

before use

Strain relief

Twist-Lock

connector

Dust cap

Vent tube

and

secured to

cable with

strap

Outboard

desiccant

attached to

cable vent

tube

(over)

Aqua

TROLL

Accessories

for Aqua TROLL

200

Connects an Aqua TROLL's RuggedCable

™

or to a controller or logger for communica-

tion via:

• Analog (4-20 mA) • RS485 Modbus

• SDI-12 • RS232 Modbus (with a customer-supplied converter)

Male Twist-Lock connector mates with female Twist-Lock connector on the RuggedCable

Stripped & tinned wires on opposite end for wiring to PLC or logger

Removable, refillable outboard desiccant protects cable vent tube from condensation in

high-humidity environments

SPECIFICATIONS

Materials PVC, titanium, nylon, Viton

Dimensions 13.33 cm (5.25 in) long, 19 mm (0.75 in) O.D.

Environmental Rating IP67 when connected, not designed for submersion

Cable 0.9 m (3 ft) vented TPU (Thermoplastic Polyurethane)

Conductors 6 conductors, 24 AWG, polypropylene insulation

Desiccant pack Clear acrylic, nylon, HDPE membrane

Desiccant approx. 22 g silica gel, type 4

Max. recommended SDI-12 61 m (200 ft)

cable lengths Modbus 1259 m (4000 ft)

4-20 mA 1259 m (4000 ft)

CONNECTIONS

Refer to wiring diagrams on back of sheet. Trim back and insulate unused wires. The

shield should be wired to a chassis ground or earth ground.

Power Connections. The Red wire provides power for all Aqua TROLL modes. The 4-

20 mA current loop output can be continuous in Modbus or SDI-12 mode as long as

Modbus device register 49507 is set to 1.

Communications. The device automatically switches between Modbus and SDI-12

modes depending on which of the two interfaces has activity. Modbus and SDI-12

cannot be used at the same time — whichever one is currently in use will block commu-

nication on the other.

To communicate with the device using Win-Situ

5 software through a serial COM port:

Disconnect the RuggedCable from the short stripped and tinned cable connector. Attach

a TROLL Com to the RuggedCable. Connect the TROLL Com's DB9-pin connector to a

serial port on a PC running Win-Situ 5.

1 2

SHORT STRIPPED & TINNED 1
Accessories 2

Résumé du contenu

Page 1 - SHORT STRIPPED & TINNED

Information SheetCatalog No. 0053310SHORT STRIPPED & TINNEDCABLEwith Male Twist-Lock ConnectorDesiccantDust cap—Removebefore useStrain reliefTwis

Page 2 - Accessories

1 800 446 7488(toll-free, US and Canada) or 970 498 1500 www.in-situ.comDue to continuing product development this information is subject to chang

Commentaires sur ces manuels

Pas de commentaire

In-situ RuggedCable for Aqua TROLL—Male connector end + st Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour l'eau In-situ RuggedCable for Aqua TROLL—Male connector end + st. In-Situ RuggedCable for Aqua TROLL—Male connector end + stripped and tinned end User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour l'eau In-situ RuggedCable for Aqua TROLL—Male connector end + st