In-situ Level TROLL 400/500/700/700H Quick Start Guide Manuel d'utilisateur télécharger pdf (Page 1)

0051120 | Rev. 008 | 09/2013

Level TROLL

400, 500, 700, and 700H

In order to deploy the instrument, complete the following

steps.

l Connect the instrument to a computer or

RuggedReader.

l Connect the instrument to the software and set up a

site and a data log.

l Install the instrument in the water. (If you are using a

level reference set it at this time.)

l Verify the installation position then disconnect the

instrument from the computer or RuggedReader.

l Secure the cable and install the desiccant.

Select a TROLL Com Communication

Device

The subsequent figure shows the function and connection

features of the TROLL Com Communication Device

models.

l A Direct-Connect TROLL Com might be preferred

for programming an instrument that will be deployed

on a suspension cable.

l A RuggedCable System and a Cable-Connect

TROLL Com are required if you intend to

communicate with the instrument while it is

deployed. However, you can program the instrument

with any TROLL Com.

l A serial (RS232) TROLL Com is required for use

with a RuggedReader Handheld PC.

Serial port on a PC/laptop and RuggedReader

Handheld PC

Cable-Connect TROLL Com Communication

Device, serial connection, for field use

Direct-Connect TROLL Com Communication

Device, serial connection, programming only, not

submersible

USB port on a PC/laptop

Direct-Connect TROLL Com Communication

Device, USB connection, programming only, not

submersible

Cable-Connect TROLL Com Communication

Device, USB connection, for field use

Connecting the RuggedCable System

Connect the Instrument to the RuggedCable

System

1. Remove the protective caps from the instrument and

cable. Ensure that the O-ring on the instrument

connection is clean.

2. Locate the flat side of each connector and notice the pins

on the instrument connector and the slots on the cable

connector.

3. Slide back the sleeve on the cable connector.

4. Position the instrument and cable flat edges so they will

connect properly. Insert the instrument connector firmly

into the cable connector.

5. Slide the cable sleeve toward the instrument until the pin

on the instrument fits into the hole in the slot on the cable

connector.

6. Hold the textured section of the sleeve in one hand and

the instrument in the other. Push and twist until you hear

a click. The click ensures the cable and instrument are

securely attached.

Connect TROLL Com Communication Device to

the RuggedCable System

1. If a desiccant is present, remove the desiccant from the

cable. Hold the textured section of the cable connector in

one hand and the desiccant in the other. Twist in

opposite directions to unlock the desiccant from the

cable.

2. Position the TROLL Com and the cable flat edges so

they will connect properly. Insert the TROLL Com

connector firmly into the cable connector.

3. Hold the textured section of the sleeve in one hand and

the TROLL Com in the other. Push and twist until you

hear a click. The click ensures the cable and TROLL

Com are securely attached.

Field Deployment

Program the Instrument

In order to set up a log or download data, you must

connect the instrument to a computer running Win-Situ 5

Software, or a RuggedReader Handheld PC running Win-

Situ Mobile. Refer to the Win-Situ 5 or Win-Situ Mobile

section. See page 2.

Position the Instrument

Place the instrument at the desired depth. Position the

instrument below the lowest anticipated water level, but

not so low that the pressure sensor range might be

exceeded at the highest anticipated water level. Refer to

the tables below to determine usable depth.

1 2 3 4

Résumé du contenu

Page 1 - 0051120

0051120 | Rev. 008 | 09/2013Level TROLL®400, 500, 700, and 700HIn order to deploy the instrument, complete the followingsteps.l Connect the instrument

Page 2 - Win-Situ 5 Software

Information subject to change without notice. In-Situ, In-Situ logo, Baro Merge, BaroTROLL, HERMIT, iSitu, Pocket-Situ, RDO, RuggedCable, RuggedReader

Page 3 - Downloading Data to a PC

0051120 | Rev. 008 | 09/2013instrument clock to the PC clock.Parameters and measurements are displayed in light grayon the home screen if a connection

Page 4 - Win-Situ Mobile Software

Information subject to change without notice. In-Situ, In-Situ logo, Baro Merge, BaroTROLL, HERMIT, iSitu, Pocket-Situ, RDO, RuggedCable, RuggedReader

Commentaires sur ces manuels

Pas de commentaire

In-situ Level TROLL 400/500/700/700H Quick Start Guide Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour l'eau In-situ Level TROLL 400/500/700/700H Quick Start Guide. In-Situ Level TROLL 400/500/700/700H Quick Start Guide User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

In-situ Level TROLL 400/500/700/700H Quick Start Guide Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour l'eau In-situ Level TROLL 400/500/700/700H Quick Start Guide. In-Situ Level TROLL 400/500/700/700H Quick Start Guide User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour l'eau In-situ Level TROLL 400/500/700/700H Quick Start Guide