In-situ Level TROLL 400/500/700/700H Quick Start Guide Manuel d'utilisateur télécharger pdf (Page 2)

Information subject to change without notice. In-Situ, In-Situ logo, Baro Merge, BaroTROLL, HERMIT, iSitu, Pocket-Situ, RDO, RuggedCable, RuggedReader, TROLL, and Win-Situ are trademarks or registered trademarks of In-Situ Inc.

A BaroTROLL Instrument can be deployed

with a non-vented instrument to compensate

level data for changes in atmospheric

pressure. Make sure the clocks on both

instruments are synchronized, and install the

BaroTROLL in a location that will never be

submerged in water.

Range Effective Range

Usable Depth

PSIA PSIA kPA Meters Feet

30 15.5 106.9 11 35

100 85.5 589.5 60 197

300 285.5 1968 200 658

500 485.5 3347 341 1120

1000 985.5 6795 693 2273

* Effective range for psia sensors is limited by an estimated 14.5

PSI atmospheric pressure at sea level.

Non-Vented Level TROLL Instrument

Range

Usable Depth

PSIG kPA Meters Feet

5 34.5 3.5 11.5

15 103.4 11 35

30 206.8 21 69

100 689.5 70 231

300 2068 210 692

500 3447 351 1153

Vented Level TROLL Instrument

Verify Instrument Depth

After you have installed the instrument, it is possible to

connect the instrument to a computer or RuggedReader,

open the software, and take a reading to verify the

installation position. If the reading confirms that the

instrument is in the correct position, you can secure it as

described below.

During log setup there was an option to "Remind Me Later"

for setting a level reference. If you set the log to remind you

later, ensure that the instrument is submerged and set the

level reference when prompted.

Secure the Cable

1 Well Dock Installation Ring

2 Kellems Grip

3 Instrument Installed in Well

Desiccant

Desiccant protects electronics from condensation, which

can cause irreparable damage and loss of data. Indicating

desiccant changes from blue to pink as it becomes

saturated with moisture.

Desiccant stages (from left)

New, nearly expired (replace now), expired

It is extremely important to use a properly-sized

desiccant for your deployment and to change desiccant

often. Desiccant should be changed before the entire

volume has turned pink, and you should use enough

desiccant to effectively keep cables, instruments, and

electrical boards dry until your next scheduled

maintenance. Desiccant life span is dependent on site

conditions.

Installing Desiccant with Twist-Lock

Connectors

1. Remove the protective dust cap from the bottom of the

desiccant pack, if applicable.

2. Remove expiring desiccant (if present) from the cable by

grasping the textured section of the cable connector in

one hand and the desiccant in the other. Twist in

opposite directions to unlock the desiccant from the

cable.

3. Attach the new desiccant pack to the twist-lock

connector on the cable.

Installing Outboard Desiccant

Vented cable must be installed with outboard desiccant to

protect the cable and instrument electronics from

condensation in high-humidity environments.

The desiccant can be removed from the vent tube, if

necessary, to trim the conductor wires. However, you must

reinstall the desiccant after trimming and connecting the

wires.

1. Cut off the knot at the bottom of the vent tube extension.

2. Firmly attach the vent tube extension to the cable vent

tube. Cover at least 6.4 mm (0.25 in.) of the cable vent

tube for a secure attachment.

3. Use the attached hook-and-loop strap to secure the

desiccant to the cable, below the stripped wires.

4. Remove the red dust cap from the black nylon cap to

allow air to reach the cable’s vent tube.

Outboard desiccant is attached to the cable

vent tube.

2 Desiccant is secured to the cable with a strap.

Safety

The instrument complies with all applicable directives

required by CE and the FCC and is found to comply with

EN 61326, ICES-003, and FCC Part 15 specifications.

Declarations of conformity may be found in the Operator's

Manual.

Win-Situ 5 Software

Use Win-Situ 5 with a laptop or a PC and the Aqua

TROLL, Level TROLL and Rugged TROLL Instruments.

To learn more about Win-Situ 5, refer to the Help menu.

Training videos are available on the In-Situ Inc. website

www.in-situ.com under Tech Resources.

Install Win-Situ 5

Insert the software CD that came with your product or

download Win-Situ 5 from the In-Situ website at www.in-

situ.com/software. Follow the on-screen prompts of the

Installation Wizard to complete installation.

IMPORTANT: Install COM drivers when prompted.

Connecting an Instrument to the Software

When you open Win-Situ 5 Software, you are asked if you

want to connect to your device. Click Yes. Synchronize the

1 2 3 4

Commentaires sur ces manuels

Pas de commentaire

In-situ Level TROLL 400/500/700/700H Quick Start Guide Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour l'eau In-situ Level TROLL 400/500/700/700H Quick Start Guide